IA2 bdbJoinUsesInstallCodeKey: Does the Trust Center policy require all nodes to join using an install code? 5.3.6 M n/a IA3 bdbPrimaryChannelSet: What is the primary channel set? 5.3.10 M 0x0318c800 IA4 bdbScanDuration: What is the scan duration? 5.3.11 M 5 IA5 bdbSecondaryChannelSet: What is the secondary channel set? 5.3.12 M 0x04e73000 IA6 bdbTCLinkKeyExchangeAttemptsMax: What is the maximum number of attempts a node will try to exchange its Trust Center link key? 5.3.14 M M 3 IA7 bdbTCLinkKeyExchangeMethod: What is the Trust Center link key exchange method? 5.3.15 M M 0x00 IA8 bdbTrustCenterNodeJoinTimeout: What is the Trust Center node join timeout? 5.3.16 M n/a IA9 bdbTrustCenterRequireKeyExchange: Does the Trust Center’s policy require a node to exchange its initial link key with a new link key generated by the Trust Center? 5.3.17 M n/a CC1 Can the product be stimulated to invoke touchlink commissioning only? O false CC2 Can the product be stimulated to invoke network formation only? O false CC3 Can the product be stimulated to invoke network steering only? O true CC4 Can the product be stimulated to invoke finding and binding only? O false CC5 Can the product be stimulated to invoke touchlink commissioning followed by network steering? O false CC6 Can the product be stimulated to invoke network formation followed by network steering? O false CC7 Can the product be stimulated to invoke network steering followed by network formation? O false CC8 Can the product be stimulated to reset before network formation? O false CC9 Can the product be stimulated to automatically form a network upon startup when factory new? O false M1 Can the node disable network steering via local application trigger? O false M2 Can the node store more than one NWK outgoing frame counters? O false M3.0 If supported, give the endpoint identifier of a cluster that has at least one writable attribute. O endpoint id or n/a M3.1 If supported (in M3.0), give the identifier of the cluster that has at least one writable attribute. O 0x0101(doorlock cluster) M3.2 If supported (in M3.0), give the attribute identifier of the writable attribute. O 0x0000 (lock state), data type 0x30, non-default value 0x01, max interval = 0x32, min interval = 0xb4, direction = 0. M4 Does the stack filter the scan channels based on a prior energy detection scan? O yes/no M5.0 If supported, give the endpoint identifier of a cluster that has at least one reportable attribute. O endpoint id or n/a M5.1 If supported (in M5.0), give the identifier of the cluster that has at least one reportable attribute. O cluster id or n/a M5.2 If supported (in M5.0), give the attribute identifier of the reportable attribute. O attribute id or n/a M6.0 If supported, give the endpoint identifier of an initiator. O endpoint id or n/a M6.1 If supported (in M6.0), give the identifier of the iniatator cluster. O cluster id or n/a M7.0 Give the number of active endpoints as returned by a touchlink scan response or an Active_EP_rsp command frame. M number of active endpoints > 0 M7.1 Give the application device identifier for the endpoint under test. M application device id M7.2 Give the application device version for the endpoint under test. M application device version M8.0 Does the node support reception of the Mgmt_NWK_Update_req ZDO command? O 0 if not supported, 1 if supported ZLT1 Is the logical device type specified as a ZigBee coordinator? [R1]/2.5.4.5.1 O.1 false ZLT1.1 Does the node encompass the role of the Trust Center? 6.1 M X X false ZLT1.2 Does the node form a centralized security network? 6.1 M X X false ZLT1.3 Does the node NOT attempt to join another network? 6.1 M false ZLT2 Is the logical device type specified as a ZigBee router? [R1]/2.5.4.5.2 O.1 false ZLT2.1 Can the router node join another network? 6.1 M false ZLT2.2 Does the node form a distributed network? 6.1 X O X false ZLT3 Is the logical device type specified as a ZigBee end device? [R1]/2.5.4.5.5 O.1 true ZLT3.1 Can the end device node join another network? 6.1 M true ZLT3.2 Is the end device sleepy? - O true ZLT4 Can the node switch between ZLT1 and ZLT2 types under application control. 6.1 O.1 false A node SHALL support one of ZLT1 or ZLT2 or ZLT3 or (ZLT1 and ZLT2, switchable under application control). NSM1 Can the node join a centralized security network? 6.2 X M M true NSM2 Can the node join a distributed security network? 6.2 X M M true LK1 Does the node contain the default global Trust Center link key? 6.3 M true LK2 Does the node contain the distributed security global link key? 6.3 M M true LK3 Does the node contain an install code derived preconfigured link key? 6.3 M M true LK4 Does the node contain the touchlink preconfigured link key? 6.3 M false UIC1 Does the node support install codes? 6.4 M true UIC2 Will the node not be available via retail channels and be professionally installed? 6.4 O.2 false UIC3 Will the node be available via retail channels? 6.4 O.2 true UIC4 Is the node configured to only require the use of install codes on joining? 6.4 O X false UIC5 Does the node have a user configuration mechanism that allows switching between a mode in which only networks that require the use of install codes for joining are considered and a mode in which all networks are considered for joining? 6.4 O.3 true UIC6 Does the node not have a user configuration mechanism that allows switching between a mode in which only networks that require the use of install codes for joining are considered and a mode in which all networks are considered for joining? 6.4 O.3 false UIC7 Does the node default to requiring potential networks to use of install codes on joining? 6.4 O X true UIC8 Can the node be switched into a mode whereby all networks are considered for joining? 6.4 M true UIC9 Can the node join all types of networks? 6.4 M false UIC10 Does the Trust Center require the use of install codes for all joining nodes? 6.4 O false One of the items marked O.2 SHALL be supported. One of the items marked O.3 SHALL be supported. GRC1.1 Does the node support network steering for a node not on a network? 6.5 M M true GRC1.2 Does the node support network steering for a node on a network? 6.5 O false GRC2.1 Is the device implemented as having a simple device class (see [R4])? 6.5 O.4 true GRC2.2 Is the device implemented as having a dynamic device class (see [R4])? 6.5 O.4 false GRC2.3 Is the device implemented as having a node device class (see [R4])? 6.5 O.4 false GRC4 Does the device support finding and binding as either an initiator or a target? 6.5 M O O true GRC4.1 Does the device provide a mechanism to invoke finding and binding on the device itself? 6.5 O false GRC5 Does the device support touchlink commissioning as either an initiator or a target or both? 6.5 O false GRC5.1 Does the device support touchlink commissioning as an initiator? 6.5 O.5 false GRC5.2 Does the device support touchlink commissioning as a target? 6.5 O.5 false GRC6 If touchlink commissioning as an initiator is attempted and is successful does the device not attempt any further commissioning operations? 6.5 M false GRC7 If network steering is attempted does the node follow the correct steering procedure dependent on whether the node is joined to a network or not? 6.5 M true GRC8 Does the node only form a network if the node is not yet joined to a network? 6.5 M M false GRC9 Can the node form a centralized network? 6.5 M false GRC10 Can the node form a distributed network? 6.5 M false GRC12 Does the node attempt finding and binding only if it is joined to a network? 6.5 M true GRC13 Does the node instigate finding and binding on one or more endpoints implemented on the node? 6.5 O false GRC14 Does the node attempt finding and binding as an initiator endpoint if the endpoint supports a type 1 client or type 2 server cluster? 6.5 O.6 false GRC15 Does the node attempt finding and binding as a target endpoint if the endpoint supports a type 1 server or type 2 client cluster? 6.5 O.6 true GRC16 Is the node capable of binding to a group during finding and binding? - O false GRC17 Is the device able to transmit groupcast messages? - O false One of the items marked O.4 SHALL be supported. One of the items marked O.5 SHALL be supported. One of the items marked O.6 SHALL be supported. MRD1 Can the node process the ZDO Active_EP_req command and respond with the ZDO Active_EP_rsp command? 6.6 M true MRD1.1 Can the node process the ZDO Node_Desc_req command and respond with the ZDO Node_Desc_rsp command? 6.6 M true MRD2 Can the node process the ZDO Simple_Desc_req command and respond with the ZDO Simple_Desc_rsp command? 6.6 M true MRD3 Can the node process the ZDO IEEE_Addr_req command and respond with the ZDO IEEE_Addr_rsp command? 6.6 M true MRD4 Can the node process the ZDO NWK_Addr_req command and respond with the ZDO NWK_Addr_rsp command? 6.6 M true MRD5 Can the node process the ZDO Match_Desc_req command and respond with the ZDO Match_Desc_rsp command? 6.6 M true MRD6 Can the node process the ZDO Mgmt_Bind_req command and respond with the ZDO Mgmt_Bind_rsp command? 6.6 M true MRD7 Can the node process the ZDO Mgmt_Lqi_req command and respond with the ZDO Mgmt_Lqi_rsp command? 6.6 M true MRD8 Can the node process the ZDO Bind_req command and respond with the ZDO Bind_rsp command? 6.6 M true MRD9 Can the node process the ZDO Unbind_req command and respond with the ZDO Unbind_rsp command? 6.6 M true MRD10 Can the node process the ZDO Mgmt_Leave_req command and respond with the ZDO Mgmt_Leave_rsp command? 6.6 M true MRD11.0 If the node supports finding and binding as an initiator, does it support the identify cluster as a client? 6.6 M false MRD11 If the node supports finding and binding as an initiator, can it process at least one identify cluster, identify query response command after broadcasting an identify cluster, identify query command? 6.6 M false MRD12 If the node supports finding and binding as an initiator, can it process more than one identify cluster, identify query response command after broadcasting an identify cluster, identify query command? 6.6 O false MRD13 If the node supports finding and binding as an initiator, does it implement a binding table whose number of entries is ≥ the sum of cluster instances supported on each device? 6.6 M false MRD14 If the node supports finding and binding as an initiator, regardless of the commissioning mechanism, is the binding table consistent such that its contents can be retrieved using the ZDO Mgmt_Bind_req command? 6.6 M false MRD16 Does the node have a cluster which is the target of an application transaction? 6.6 O false MRD17 Does the node support group addressing and at least 8 memberships in the group table? 6.6 M false DRC1 Does the node have at least one attribute that is specified as mandatory and reportable? 6.7 O true DRC2 Does the node have a default reporting configuration for every attribute that is specified as mandatory and reportable? 6.7 M true DRC3 Does the node automatically send reports to a node that binds with a cluster containing an attribute that is specified as mandatory and reportable? 6.7 M true DRC4 If any default reporting configuration is overwritten, is the updated reporting configuration used instead? 6.7 M true DRC5 If the maximum reporting interval of an attribute is greater than 0x0000, is a report generated when the time that has elapse since the previous report of the same attribute is equal to the maximum reporting interval for that attribute? 6.7 M true DRC6 If the maximum reporting interval of an attribute is equal to 0x0000, is a report generated when the attribute value changes? 6.7 M true MDP1 Is the MAC data polling rate dynamic based on the operating state of the node? 6.8 R true MDP2 Does the node have at least a fast and a slow MAC data polling rate? 6.8 R true MDP3 Does the device poll more frequently than once per 7.5 seconds? 6.8 R true MDP4 While waiting for an active response message, does the node poll at its fast rate? 6.8 R true MDP5 Is the fast poll rate at least once every 3 seconds? 6.8 R true MDP6 While not actively waiting for messages, does the node poll at its slow rate? 6.8 O true MDP7 Does the node poll at its fast rate during commissioning? 6.8 R true ZPD1 Does the node preserve the value of the bdbNodeIsOnANetwork attribute across resets? 6.9 M true UGP1 Does the node support the Green Power proxy basic functionality? 6.10 M M O false INP1 Does the node support the initialization procedure? 7.1 M true INP2 Does the node restore its persistent ZigBee data? 7.1 M true INP3 If the node is a ZigBee End Device and was previously on a network, does it attempt to rejoin the network? 7.1 M true INP4 On successful rejoining, does the node broadcast a device_annce ZDO command? 7.1 M true INP5 If the node is a ZigBee Router and supports touchlink but was not previously on a network, does it switch to a touchlink primary channel? 7.1 M false COM1 Does the implementation provide a mechanism to invoke network steering? 8 M true COM2 Does the implementation provide a mechanism to invoke finding and binding? 8 M true NSO1 Is the network steering for a node on a network procedure supported? 8.2 O false NSO2 Does the node first broadcast the Mgmt_Permit_Joining_req ZDO command? 8.2 M false NSO3 If the node is a ZigBee Coordinator or a ZigBee Router, does the node activate its permit joining flag for ≥ bdbcMinCommissioningTime? 8.2 M false NSN1 Is the network steering for a node not on a network procedure supported? 8.3 X M M true NSN2 Does the node attempt to discover networks over a set of channels? 8.3 M true NSN3 If suitable networks were found, does the node attempt to join one of them using MAC association? 8.3 M true NSN4 If the join was not successful and there are more suitable networks to join, does the node attempt to join another network? 8.3 M true NSN5 If the join was successful, does the node wait apsSecurityTimeOutPeriod milliseconds to receive the network key? 8.3 M true NSN6 If the network key is not received within apsSecurityTimeOutPeriod milliseconds, the network key is received but could not be decrypted or the authentication fails does the node reset its network parameters? 8.3 M true NSN7 Does the node broadcast a Device_annce ZDO command? 8.3 M true NSN9 If the TC link key exchange is not successful, does the node reset its network parameters and remove itself from the network? 8.3 M true NSN10 If the TC link key exchange is successful, does the node broadcast the Mgmt_Permit_Joining_req ZDO command? 8.3 M true NSN11 Does the node activate its permit joining flag if new nodes can join this node? 8.3 M false NFP1 Is the network formation procedure supported? 8.4 M O false NFP2 Does the node attempt to form a network over a set of channels? 8.4 M false NFP3 If formation is successful and the node is a ZigBee Coordinator, does it initiate its Trust Center functionality? 8.4 M false FBT1 Is the finding & binding for a target endpoint procedure supported? 8.5 M true FBT2 Does the target identify itself for at least bdbMinCommissioningTime seconds? 8.5 M true FBT3 Does the target respond to Identify cluster Identify Query commands? 8.5 M true FBI1 Is the finding & binding for an initiator endpoint procedure supported? 8.6 M false FBI2 Is the Identify cluster Identify Query command broadcast supported? 8.6 M false FBI3 Is the simple descriptor of each respondent obtained with the Simple_Desc_req ZDO command? 8.6 M false FBI4 Does the initiator create a binding table entry for each matching cluster to the respondent? 8.6 M false FBI5 If a group binding is requested, does the initiator add the respondent to an appropriate group? 8.6 M false TLI1 Is the touchlink for an initiator procedure supported? 8.6 M false TLI2 Does the initiator broadcast 5 scan request inter-PAN command frames on the first primary touchlink channel and then once for each remaining primary channel? 8.6 M false TLI3 Does the initiator broadcast a scan request inter-PAN command frames on each secondary touchlink channel when using touchlink for formation or joining? 8.6 O false TLI4 If the initiator is not on a network, does it ignore any scan request command frames from other factory new initiators? 8.6 M false TLI5 If the initiator is not on a network, does it switch into a target mode if any scan request command frames are received from other non-factory new initiators? 8.6 O false TLI6 If a target is found, does the initiator transmit a device information request inter-PAN command frame to the selected target? 8.6 O false TLI6.1 If a device information request inter-PAN command frame is sent to the selected target but no response is received, does the initiator terminate the touchlink procedure for an initiator? 8.6 O false TLI7 If a target is found, does the initiator transmit one or more identify request inter-PAN command frame to the selected target? 8.6 O false TLI8 If a scan request command frame is received from a target on the same network as the initiator with the network update identifier field lower than nwkUpdateId, does the initiator transmit a network update request inter-PAN command frame to the selected target and then terminate the touchlink procedure? 8.6 M false TLI9 If a target is found on a different network to the initiator and the initiator is on a centralized network, does it terminate the touchlink procedure? 8.6 M false TLI10 If the initiator is not on a network and the target is a ZigBee Router, does the initiator transmit a network start request inter-PAN command frame to the selected target? 8.6 M false TLI11 If the initiator is on a network and the target is a ZigBee Router, does the initiator transmit a network join router request inter-PAN command frame to the selected target? 8.6 M false TLI12 If the initiator is on a network and the target is a ZigBee End Device, does the node transmit a network join end device request inter-PAN command frame to the selected target? 8.6 M false TLI13 If the initiator is an end device and a network start request inter-PAN command frame was sent to the selected target, does the node rejoin the network? 8.6 M false TLT1 Is the touchlink for a target procedure supported? 8.7 M false TLT2 Does the target discard any touchlink commissioning command other than a scan request command and terminate the procedure? 8.7 M false TLT3 Does the target discard scan request command frames with an RSSI lower than a product specific threshold and terminate the procedure? 8.7 M false TLT4 Does the target respond to a scan request command frame with a scan response command frame? 8.7 M false TLT5 Does the target respond to a device information request command frame with a device information response command frame? 8.7 M false TLT6 Does the target identify itself on receipt of a identify request command frame? 8.7 M false TLT7 Does the target allow starting a new network or joining another network when not factory new (i.e. stealing)? 8.7 O false TLT7.2 If the target receives a network start request command frame, is a ZigBee Router and decides not to start a network, does it respond with a network start response command frame with the Status field set to 0x01 (failure)? 8.7 M false TLT7.3 If the target receives a network start request command frame, is a ZigBee Router and decides to start a network, does it perform a network discovery? 8.7 M false TLT8.1 If the target receives a network join router request command frame, is a ZigBee Router and decides not to be joined to another network, does it respond with a network join router response command frame with the Status field set to 0x01 (failure)? 8.7 M false TLT8.2 If the target receives a network join router request command frame, is a ZigBee Router and decides to join the network of the initiator, does it respond with a network join router response command frame with the Status field set to 0x00 (success)? 8.7 M false TLT9.1 If the target receives a network join end device request command frame, is a ZigBee End Device and decides not to be joined to another network, does it respond with a network join end device response command frame with the Status field set to 0x01 (failure)? 8.7 M false TLT9.2 If the target receives a network join end device request command frame, is a ZigBee End Device and decides to join the network of the initiator, does it respond with a network join end device response command frame with the Status field set to 0x00 (success)? 8.7 M false TLT10 If the target is already part of a network when it receives a network start request, network join router request or a network join end device request command and permits stealing, does it leave its current network? 8.7 M false TLT11 If the target router is already part of a network when it receives a network start request command and the target router permits stealing, does the target router start a new network? 8.7 M false TLT12 After starting a new network, does the target router direct join the initiator to its new network? 8.7 M false RBC1 Does the target support reception of the reset to factory defaults command frame? 9.1 O true RBC2 Does the initiator transmit a reset to factory defaults command frame to a target? 9.1 O false RBC3 On receipt of a reset to factory defaults command frame, does the target reset all attributes of all clusters to their default values? 9.1 M true RBC4 On receipt of a reset to factory defaults command frame, does the target not reset its network parameters? 9.1 M true RTL2 Does the initiator transmit a reset to factory new command frame to a target? 9.2 M false RTL3 On receipt of a reset to factory new command frame and if the target is on a distributed security network, does it leave the network? 9.2 M false RTL4 On receipt of a reset to factory new command frame and if the target is on a centralized security network, does it ignore the command? 9.2 O false RTL5 Does the initiator use an extended channel scan during a reset via the touchlink commissioning cluster? 9.2 M false RNL1 Does a node transmit a leave NWK command frame to another node to trigger the other node to leave? 9.4 O false RNL2a On receipt of a leave NWK command frame with the request bit set to 1 when the nwkLeaveRequestAllowed NIB attribute is set to TRUE, does the node leave the network? 9.4 M false RNL2b On receipt of a leave NWK command frame with the request bit set to 1, does the end device node leave the network? 9.4 M true RLZ1 Does a node transmit an Mgmt_Leave_req ZDO command frame to another node? 9.5 O false RLZ2a On receipt of an Mgmt_Leave_req ZDO command frame when the nwkLeaveRequestAllowed NIB attribute is set to TRUE, does the node leave the network? 9.5 M true RLZ2b On receipt of an Mgmt_Leave_req ZDO command frame, does the end device node leave the network? 9.5 M true RLA1 Does the node provide a local reset mechanism? 9.6 O true RLA2 On activation of the local reset mechanism, does the node reset itself? 9.6 M true RLK0 Does the node exchange its link key during network steering on a centralized security network? 10.2.5 M M true RLK1a Does the node execute the appropriate steps defined by the alternative link key exchange mechanism? 10.2.5, step 1 M false RLK1b If the alternative mechanism is successful, does the node terminate the node link key exchange procedure? 10.2.5, step 1 M false RLK3 If the APS Request Key method is used or the alternative mechanism is not successful, does the node transmit the Node_Desc_req ZDO command to the Trust Center? 10.2.5, step 3 M M true RLK4a If a Node_Desc_rsp ZDO command is not received within bdbcTCLinkKey-ExchangeTimeout seconds does the node retry up to the maximum attempts permitted? 10.2.5, step 4 M true RLK4b If a Node_Desc_rsp ZDO command is not received after the maximum number of attempts permitted, does it terminate the node link key exchange procedure? 10.2.5, step 4 M true RLK5 If a Node_Desc_rsp ZDO command is received and the server mask of the node descriptor indicates a core stack of r20 or earlier, does the node terminate the node link key exchange procedure? 10.2.5, step 5 M true RLK7 If a Node_Desc_rsp ZDO command is received and the server mask of the node descriptor indicates a core stack of r21 or later, does the node request a new link key using the Request Key APS command frame to the Trust Center, encrypted with its initial link key? 10.2.5, step 7 M true RLK8a If a Transport Key APS command is not received within bdbcTCLinkKey-ExchangeTimeout seconds does the node retry up to the maximum attempts permitted? 10.2.5, step 8 M true RLK8b If a Transport Key APS command is not received after the maximum number of attempts permitted, does it terminate the node link key exchange procedure? 10.2.5, step 8 M true RLK9 If a Transport Key APS command frame is received from the Trust Center, containing a new link key, does the node update its Trust Center link key with the new key? 10.2.5, step 9 M true RLK11 Does the node verify the new key using the Verify Key APS command frame to the Trust Center? 10.2.5, step 11 M true RLK12a If a Confirm Key APS command is not received within bdbcTCLinkKey-ExchangeTimeout seconds does the node retry up to the maximum attempts permitted? 10.2.5, step 12 M true RLK12b If a Confirm Key APS command is not received after the maximum number of attempts permitted, does it terminate the node link key exchange procedure? 10.2.5, step 12 M true AIC0 Does the Trust Center allow the input of an install code? 10.3.1 O false AIC2 On receipt of an installation code, does the Trust Center create an entry in its node/link key mapping table (apsDeviceKeyPairSet) with the installation code derived key? 10.3.1, step 2 M false ANN1 On receipt of an Update Device APS command frame, does the Trust Center follow the procedure for adding a new node into the network? 10.3.2 M false ANN2 If an install code is required and the new node is not in apsDeviceKeyPairSet, does the Trust Center terminate the Trust Center link key exchange procedure? 10.3.2 M false ANN3 If an install code is not required and the new node is not in apsDeviceKey-PairSet, does the Trust Center create an entry in its apsDeviceKeyPairSet for the joining node? 10.3.2 M false ANN4 Does the Trust Center send the network key to the joining node using a Transport Key APS command frame, encrypted with the entry in apsDeviceKeyPairSet corresponding to the joining node? 10.3.2 M false ANN5 If a Request Key APS command frame is not received and the Trust Center requires the new node to exchange its link key, does it request the new node leaves the network? 10.3.2 M false ANN6 On receipt of a Request Key APS command frame from the joining node, encrypted with its initial link key, does the Trust Center generate a new link key and transport it to the joining node using a Transport Key APS command frame? 10.3.2 M false ANN7 If a Verify Key APS command frame is not received by the Trust Center from the joining node, does it request the new node leaves the network? 10.3.2 M false ANN8 Does the Trust Center receive a Verify Key APS command frame from the joining node, update the entry in apsDeviceKeyPairSet corresponding to the joining node with the new key and respond with a Confirm Key APS command frame? 10.3.2 M false BKN1 Does the Trust Center allow a known node to join but in a fresh state? 10.3.3 M false BKN2 Does the Trust Center store the original install code derived link key for devices that have joined? 10.3.3 O false BKN3 Does the Trust Center overwrite the link key for a joining node with the original install code derived link key? 10.3.3 M false BKN4 Does the Trust Center overwrite the link key for a joining node with the default global Trust Center link key? 10.3.3 M false TCP1.1 Does the Trust Center allow any nodes to join (Trust Center policy useWhiteList)? [ZIGBEE] Table 4.33 O.7 false TCP1.2 Does the Trust Center allow only known nodes to join (Trust Center policy useWhiteList)? [ZIGBEE] Table 4.33 O.7 false TCP2.1 Does the Trust Center allow a node on the network that transmits a ZDO Mgmt_Permit_Join with a significance set to 1 to affect the Trust Center policy (Trust Center policy allowRemoteTc-PolicyChange)? [ZIGBEE] Table 4.33 O.8 false TCP2.2 Does the Trust Center forbid a node on the network that transmits a ZDO Mgmt_Permit_Join with a significance set to 1 to affect the Trust Center policy (Trust Center policy allowRemoteTc-PolicyChange)? [ZIGBEE] Table 4.33 O.8 false One or both of the items marked O.7 SHALL be supported. One or both of the items marked O.8 SHALL be supported.